Protective & Functional Coatings · Manufacturing & SupplyFor distributors, contractors & industrial buyers
LEADERCOATPROTECTIVE & FUNCTIONAL COATINGS
中文Request a Quote
Home/Products/Waterproofing & Repair Materials
LEADERCOAT

Waterproofing & Repair Materials

Select materials after identifying the substrate and the path of water entry. Waterproof coatings, crystalline treatments, transparent surface coatings and epoxy repairs perform different tasks. Repair unstable joints and substrate defects before relying on a surface coating.

Request a Quote ↗
SELECTION PRINCIPLES

What determines the right system

Waterproofing layers, surface repairs and supporting resins

Find the water path

Surface absorption, cracks, joints and drainage faults require different responses. A coating selection should follow an assessment of the defect and water-pressure direction.

Match movement and substrate

A rigid repair and a flexible waterproof layer serve different functions. Identify active movement, dampness, loose material and any existing finish before defining the system.

Distinguish resin from coating

A supporting resin may require formulation, a curing system or reinforcement. It should not be specified as a ready-to-apply waterproof coating without defining the complete use system.

Choose a coating type

Each type addresses a different protection or application requirement. Open a category to review its selection details.

Crystalline Waterproofing Coatings

Cement-based surface treatments for compatible concrete

Explore category

Liquid Waterproofing Coatings

Site-applied waterproofing layers for defined substrates

Explore category

Transparent Waterproofing Coatings

Surface waterproofing where the visible finish matters

Explore category

Epoxy Repair Materials

Resin-based repairs selected for defect and placement

Explore category

Supporting Resins

Resin supply for defined formulation and application systems

Explore category
Compare the selection focus
CategorySelection focus
Crystalline Waterproofing CoatingsThis category is for surface-applied treatments on suitable cement-based substrates. Paint, tiles, contamination and weak surface material can prevent proper contact with the concrete.
Liquid Waterproofing CoatingsA membrane under tile and an exposed roof finish have different demands. State sunlight, traffic, ponding and any intended protective or decorative layer.
Transparent Waterproofing CoatingsWater may pass through grout, joints, cracks or concealed failures. A transparent surface layer should be selected only after identifying the path and necessary repairs.
Epoxy Repair MaterialsA non-sag putty, trowelable mortar and flowing grout solve different placement problems. Provide repair dimensions, orientation and access so the material form can be matched.
Supporting ResinsCommercial names alone may not define chemistry. State the required resin family and whether it serves as a binder, impregnation resin or another formulation input.
USE & EXPOSURE

Application requirements

Identify the defect and water path before choosing a treatment. Substrate repairs, movement details and the waterproofing layer need to work together.

01

Concrete and cement-based waterproofing

02

Tiled surfaces requiring a transparent finish

03

Local repairs and resin-based repair systems

Application areas describe the selection scope. Suitability is determined for the specific material and actual operating conditions.

PURCHASING BRIEF

Prepare your enquiry

Include the following details with your quantity, destination and packaging requirements. A project specification or required test method helps define the material assessment.

Discuss your requirements ↗
  1. Substrate, existing finish and defect location
  2. Water source and direction of exposure
  3. Crack or joint movement and moisture condition
  4. Required finish and access for preparation

Questions before selection

Can a transparent coating fix every leak without removing tiles?

That depends on the water path and substrate condition. Moving joints, concealed defects and drainage faults may need repairs beyond a surface coating.

Is crystalline coating suitable for every surface?

It is selected for compatible cement-based substrates. Non-cement surfaces and areas subject to movement require a different material assessment.

LEADERCOAT

Start with your application.

Share the substrate, operating conditions and supply requirement. Let’s define the coating category and the details needed for your quotation.

Request a Quote ↗

Search products

Anti-Corrosion Coatings & LiningsProtection for metal, equipment and process surfacesPeelable & Temporary Protective CoatingsSurface protection and masking with a defined removal methodGlass CoatingsPrivacy, light control and removable glass finishesWaterproofing & Repair MaterialsWaterproofing layers, surface repairs and supporting resinsGlass Flake & Vinyl Ester CoatingsBarrier coatings and resin systems for process environmentsHigh-Temperature CoatingsProtective finishes for heat-exposed metalMetal Protective TopcoatsExterior finish layers for compatible protective systemsZinc-Rich CoatingsZinc-rich layers within steel protection systemsTank & Pipe LiningsInternal protection selected for the contained mediumWear-Resistant CoatingsProtection selected for the actual wear mechanismMulti-Surface Peelable CoatingsRemovable protection for installation and handlingLiquid Masking CoatingsApplied masks for controlled paint-process boundariesAutomotive Peelable CoatingsSpray-applied removable finishes for compatible vehicle surfacesWater-Removable Temporary CoatingsTemporary films selected for a water-removal processElectronic Protection & Masking MaterialsTemporary masks for defined electronic processesFrosted Glass Privacy CoatingsDiffused daylight with reduced visibilityOpaque Glass CoatingsOpaque finishes for visual screeningPeelable Frosted Glass CoatingsRemovable privacy finishes with a frosted effectCrystalline Waterproofing CoatingsCement-based surface treatments for compatible concreteLiquid Waterproofing CoatingsSite-applied waterproofing layers for defined substratesTransparent Waterproofing CoatingsSurface waterproofing where the visible finish mattersEpoxy Repair MaterialsResin-based repairs selected for defect and placementSupporting ResinsResin supply for defined formulation and application systemsIPN8710 Anti-Corrosion Pipe & Tank LiningA continuous internal barrier protects water-handling surfaces and supports a smooth, maintainable lining. The primer establishes adhesion while the finish forms the water-contact surface.Acrylic Polyurethane Metal TopcoatCombines an exterior colour finish with a protective top layer for structural steel and equipment. Colour and gloss can be coordinated across machinery, frames and fabricated parts.Vinyl Ester Glass Flake MasticOverlapping glass flakes create a longer penetration path through the resin lining. The mastic form allows a substantial barrier to be built around vessels, ducts and chemical containment details.Modified Vinyl Ester Protective CoatingProvides a resin-based protective surface for chemical processing and wastewater infrastructure. The coating can be arranged as a primer, protective build and finish to cover both broad areas and detailed connections.Coal Tar Epoxy Pipe CoatingCombines an epoxy binder with a bituminous barrier for buried and wet-service infrastructure. Its dark film suits pipe exteriors and protected surfaces where barrier protection is the main requirement.901 Epoxy Vinyl Ester ResinA resin base for corrosion-resistant composites, linings and formulated protective materials. Its liquid form supports fibre wet-out and the production of shaped composite parts or reinforced surface layers.Urushiol Titanium Protective CoatingA specialist protective finish for industrial equipment and surfaces facing chemical exposure. It forms an adherent barrier and can be incorporated into maintenance coating systems for tanks, pipework and plant surfaces.Epoxy Repair PuttyA paste-grade repair material for local voids, edge defects and surface levelling. The non-flowing application form helps place material into small cavities and prepare a sound surface for subsequent coating.Epoxy Repair MortarA resin-and-aggregate repair material for rebuilding worn or damaged concrete profiles. It supports deeper local repairs, floor edges and equipment bases that require a shaped, load-bearing repair layer.Silicone Aluminum Heat-Resistant CoatingA metallic heat-resistant finish for hot pipework and industrial equipment. The aluminium-pigmented surface provides a silver appearance while the silicone binder serves the elevated-temperature coating duty.Silicon Carbide Wear-Resistant CoatingHard silicon carbide particles form the working wear surface within a binding matrix. The material suits equipment exposed to abrasive particles, including pump components, chutes and slurry-handling details.High-Temperature Chloride-Exposure CoatingProtective coating selection for equipment where heat and chloride-bearing exposure occur together. The system is configured around the gas or liquid phase, temperature cycle and surface conditions of the process.Epoxy FRP Pipe Lining SystemA reinforced internal lining combines the barrier function of epoxy with glass-fibre support. The layered construction allows the lining arrangement to follow pipe geometry, connections and service requirements.Silicone High-Temperature CoatingA silicone-based protective finish for exhausts, hot pipework, ovens and other heated metalwork. The coating is selected around operating temperature, heating cycles and the required surface appearance.Chlorinated Rubber Marine Protective CoatingAn industrial and marine maintenance coating for exposed steelwork and equipment. Its film-forming system supports practical recoating and colour finishing within a compatible protective build.Cold-Applied Zinc-Rich CoatingA zinc-rich coating restores protective coverage at cut edges, welds and damaged galvanized areas. It also supports maintenance protection on small steel components and difficult-to-access details.Conductive Tank LiningCombines corrosion protection with a conductive path through the tank-lining system. It is used where tank operation requires electrostatic control alongside protection of the metal surface.Modified Epoxy Process Tank LiningA smooth epoxy lining for process equipment requiring cleanable internal surfaces. The lining design brings together the contact medium, cleaning cycle and maintenance needs of the food-processing operation.Light-Colored Conductive Epoxy CoatingA light-coloured conductive lining supports internal visibility while providing electrostatic control. Non-carbon conductive fillers allow the lining appearance to be coordinated with tank inspection and maintenance needs.Epoxy Phenolic Tank TopcoatA crosslinked epoxy-phenolic lining for chemical storage and process containment. The system is designed around the stored medium, immersion duty and cleaning sequence to form a continuous internal barrier.Epoxy Zinc-Rich PrimerA zinc-rich epoxy base layer protects prepared steel and provides the starting point for a multi-coat corrosion system. It works with barrier intermediates and weather-resistant finishes on structures and equipment.Epoxy Glass Flake CoatingGlass flakes reinforce an epoxy barrier to extend the route that moisture and process media travel through the film. The coating suits protective lining systems and heavy-duty surface protection.Solvent-Free Epoxy Tank LiningA solvent-free epoxy system builds a continuous protective lining inside tanks and containment structures. The formulation supports substantial film build with the application process organised around mixing and curing.Epoxy Crack Injection ResinA flowing epoxy resin fills accessible static cracks and bonds the prepared crack faces. Injection allows material to enter the crack path and supports local restoration of concrete continuity.Fluoropolymer Metal TopcoatAn exterior finishing system for metalwork where weathering and appearance retention are central requirements. It provides a colour-coordinated top layer for structures, equipment and architectural metal components.Ceramic-Filled Epoxy Wear LiningCeramic particles in an epoxy matrix create a rebuildable wear surface for particle-handling equipment. The lining can restore profiles and protect elbows, housings and chutes exposed to abrasive flow.Multi-Surface Peelable Protective CoatingForms a continuous removable film over finished surfaces during installation and handling. The liquid application follows contours and covers awkward shapes, while the film is peeled away after the protection period.Water-Based Elastic Peelable CoatingA water-carried coating dries into a flexible temporary film. Elasticity supports continuous peeling around contours and allows the film to protect finished components through handling and installation.Peelable Wheel Colour SprayAdds a removable colour finish to vehicle wheels for styling and refurbishment. The spray format reaches spokes and contours while allowing the original finish to be revealed when the film is removed.Peelable Liquid Protection for ComponentsCreates temporary coverage during fabrication, assembly and transport. It can cover large panels or shaped parts where a liquid-applied film helps simplify protection of the complete surface.Spray-On Removable Automotive CoatingA removable coating gives vehicle panels a coordinated colour finish without using sheet film. Spray application follows complex body contours and supports a consistent appearance across adjoining panels.Peelable Mask for Metal ProcessingDefines protected areas during selected metal-treatment operations. The coating follows edges and recesses to form a removable mask, helping separate working surfaces from areas that should remain covered.Water-Washable Temporary Vehicle ColourCreates short-term visual markings and colour effects for vehicle displays, events and promotional work. The finish is designed around later washing, making it useful for applications with a planned removal time.Peelable Frosted Glass CoatingCombines a diffused glass appearance with later film removal. It suits changing interior layouts, temporary privacy zones and decorative glazing where the finish needs to be renewed or removed.Water-Removable Temporary ProtectionProtects a surface through temporary handling or processing with a water-based removal route. It suits operations where access to wash equipment makes rinsing a practical part of the finishing sequence.Clear Peelable Furniture Protection SprayAdds a transparent removable film while keeping the underlying finish visible. It is intended for finished decorative surfaces where temporary coverage and later peeling are part of the protection plan.Peelable Aerosol Protective SprayProvides a portable spray format for temporary protection and removable finishes. The aerosol is convenient for smaller parts, local protection areas and maintenance work where a spray gun is unnecessary.Peelable PCB Solder MaskMasks selected circuit-board areas during soldering and assembly. The temporary film covers connectors, holes or keep-out zones and is removed after the protected production stage.Peelable Liquid Paint MaskA liquid mask covers broad or irregular areas against paint overspray. It follows the surface contour and is peeled away with the captured overspray after the painting operation.Peelable Blue Glue for LCM ProcessingA temporary protective adhesive for selected liquid-crystal-module operations. Local application supports defined protection boundaries around sensitive assembly areas, with removal built into the process sequence.Peelable Blue Coating for LCD & ITOProvides temporary patterned protection on selected display and conductive-glass surfaces. Controlled coating placement helps define the areas exposed to processing and the areas protected until removal.Translucent Frosted Glass Privacy CoatingCreates a frosted privacy finish that diffuses the view while retaining soft daylight. It suits offices, bathrooms and interior partitions where a screened view and natural light are both desired.Opaque Privacy Glass CoatingForms a covering finish for glass where visual screening takes priority. It suits private rooms, back-of-house glazing and display-window areas needing a stronger reduction of visibility and transmitted light.Cementitious Crystalline Waterproofing CoatingActive components work within the concrete pore structure to restrict water pathways. The mineral treatment integrates with the substrate and suits concrete tanks, basements and water-retaining structures.Qingning Polyurethane Waterproofing CoatingA liquid-applied polyurethane layer provides continuous waterproofing around complex concrete surfaces. It suits tank walls, channels and construction details that benefit from a joint-free coating.Water-Based Roof Waterproofing CoatingA liquid-applied roof membrane follows roof contours and details to form a continuous protective surface. It suits roof refurbishment where broad areas, upstands and penetrations need an integrated coating.Clear Waterproofing Coating for TilesForms a clear protective layer over an existing decorative surface. It supports accessible surface waterproofing and local repair while keeping the colour and pattern of the underlying finish visible.Two-Component Polymer-Cement Waterproofing SlurryCombines a polymer liquid and cementitious powder to form a waterproof layer on mineral substrates. It fits wet-area construction beneath later finishes, with continuous treatment around corners and pipe penetrations.